0 Replies Latest reply: Jan 14, 2020 7:29 AM by zukok@stifel.com RSS

    having telnet issues when using virl

    zukok@stifel.com

      Hi all,

       

      I have just completed the install of Virl on bare metal and so far everything looks good. I was able to launch VM Maestro and was able to load the downloaded IOS versions on to it. The only issue that I currently have is when I start my lab under the simulations section I see the following

       

      virl1.PNG

       

      My IOS device says it's UNREACHABLE

       

      Also when I try to Telnet to it (it's management address) I see nothing happen. I am assuming that is because the device is UNREACHABLE. Can someone explain why it's in that state?

       

      Also here is my ifconfig output from my jump host

       

      @mgmt-gIVX3e$ ifconfig

      eth0      Link encap:Ethernet  HWaddr fa:16:3e:38:2b:87 

                inet addr:172.16.1.58  Bcast:172.16.1.255  Mask:255.255.255.0

                inet6 addr: fe80::f816:3eff:fe38:2b87/64 Scope:Link

                UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

                RX packets:200900 errors:0 dropped:0 overruns:0 frame:0

                TX packets:201626 errors:0 dropped:0 overruns:0 carrier:0

                collisions:0 txqueuelen:1000

                RX bytes:28364002 (28.3 MB)  TX bytes:40970924 (40.9 MB)

       

       

      eth1      Link encap:Ethernet  HWaddr 5e:00:40:02:00:00 

                inet addr:10.255.0.47  Bcast:10.255.255.255  Mask:255.255.0.0

                inet6 addr: fe80::5c00:40ff:fe02:0/64 Scope:Link

                UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1

                RX packets:100953 errors:0 dropped:0 overruns:0 frame:0

                TX packets:40200 errors:0 dropped:0 overruns:0 carrier:0

                collisions:0 txqueuelen:1000

                RX bytes:7565506 (7.5 MB)  TX bytes:1689420 (1.6 MB)

       

       

      eth-int   Link encap:Ethernet  HWaddr 96:01:ae:96:93:5d 

                inet6 addr: fe80::9401:aeff:fe96:935d/64 Scope:Link

                UP BROADCAST RUNNING MULTICAST  MTU:9000  Metric:1

                RX packets:409554 errors:0 dropped:0 overruns:0 frame:0

                TX packets:33 errors:0 dropped:0 overruns:0 carrier:0

                collisions:0 txqueuelen:1000

                RX bytes:48471862 (48.4 MB)  TX bytes:2406 (2.4 KB)

       

       

      lo        Link encap:Local Loopback 

                inet addr:127.0.0.1  Mask:255.0.0.0

                inet6 addr: ::1/128 Scope:Host

                UP LOOPBACK RUNNING  MTU:65536  Metric:1

                RX packets:80334 errors:0 dropped:0 overruns:0 frame:0

                TX packets:80334 errors:0 dropped:0 overruns:0 carrier:0

                collisions:0 txqueuelen:1000

                RX bytes:7872444 (7.8 MB)  TX bytes:7872444 (7.8 MB)

       

      All of my management addresses that are being assigned to the devices are in the eth1 range... 10.255.0.0/16

      What am I doing wrong?

       

      From the jump host I am not able to ping any of the management ip addresses that are assigned to the routers in the lab

       

      Thanks