11 Replies Latest reply: May 31, 2010 12:46 PM by BBK RSS

    http://www.myrouterlab.com/

    rishi

      Guys


      plzz share ur views abou http://www.myrouterlab.com/


      its also free rack rental


      but cant remove old configs on the routers


      it just wont let me change IP for serial & ethernet intefaces


      regards


      R

        • 1. Re: http://www.myrouterlab.com/
          Angela

          I'll try it out in a few days, let's see what will happen...

          • 2. Re: http://www.myrouterlab.com/
            Pawel

            Hi,

             

            try to reed that

             

            http://www.myrouterlab.com/cgi/myrouterlab.cgi?action=howto

             

             

            some of the commands are restricted.

             

             

             

            Pawel

            • 3. Re: http://www.myrouterlab.com/
              rishi

              Pawel

               

              i hav read dat document

               

              but we cant assign new ip addresses to any interfaces & we cant erase the existing config

               

              they have around 4 routers & 2 switches

               

              wats d use if we cant do our own ip addressing shceme

               

              regards

               

              R

              • 4. Re: http://www.myrouterlab.com/
                rishi

                Angela

                 

                hav u tried rack available at myrouterlab.com

                 

                can u share ur experience

                 

                regards

                 

                R

                • 5. Re: http://www.myrouterlab.com/
                  Angela

                  Well, let's just say I would rather wait for the busy schedule at packetlife.net. That website is not really what you want to use. I'm doing a lab session right now, but I think I'll pass. There are lots of previous configs you can't erase, with lots of annoying stuff, error messages keeps showing up. I can' enter Router 3 and the administrator's email address can't be reached. Not sure what I can do with these stuff

                  • 6. Re: http://www.myrouterlab.com/
                    rishi

                    thanxx for dat Angela

                     

                    actually i found an issue with packetlife as well

                     

                    the other day i was logged in to rack but cudnt access SW2

                     

                    whenever i wud try SSHing SW2

                     

                    i wud get SW1

                     

                    i was using correct IP and correct port though

                     

                    which rack rentals wud b gud and also cheap

                     

                    kindly suggest

                     

                    i looked at INE but its 2 expensive

                     

                     

                     

                     

                     

                    Regards

                     

                    R

                    • 7. Re: http://www.myrouterlab.com/
                      Deepak

                      For me it doesn't matter really, because use any IP addressing scheme and any routing protocol is gonna behave as it should...so main focus must be to grasp funda behind routing protocols for example...OSPF.

                       

                      Regards,

                      Deepak

                      • 8. Re: http://www.myrouterlab.com/
                        BBK

                        Multi-post

                        • 9. Re: http://www.myrouterlab.com/
                          BBK

                          Multi-post

                          • 10. Re: http://www.myrouterlab.com/
                            BBK

                            Multi-post

                             

                            Apparently the server was going down for maintenance while I was attempting to post my reply.

                            • 11. Re: http://www.myrouterlab.com/
                              BBK

                              Hello Guys,

                               

                                   I was just playing around with myrouterlab.com for the first time and found th "lab diagram (http://www.myrouterlab.com/cgi/diagram.html) quite usfull.

                               

                              I will really need to study the topology a bit more to figure out how to start using it.

                               


                              Also note that the configuration files need to be named with the perscribed names:

                               

                              router1.config

                               

                              router2.config

                               

                              router3.config

                               

                              router4.config

                               

                              switch1.config

                               


                              as per the howto (http://www.myrouterlab.com/cgi/tftp_howto.html)

                               

                              and then tftp them to the tftp server @ 192.168.0.2 before then end of your session

                               

                              Appearently they will be loaded back in again when you next login thith your account.

                               


                              I am still trying to figure out why all the devices are configured the way they are by default. All those sub interfaces?

                               


                              Not sure if it was left over from someone else or it is ny design?

                               


                              I deleted my router4.config file and reloaded and it still came up with the same configuration.

                               

                              I still don't understand it yet.

                               


                              I was able to configure ip address's on R4's S1/1 interface without incident.

                               


                              Before:

                               

                              -------------------------------------------

                               

                              Router4>sh ip int brief
                              Interface                  IP-Address      OK? Method Status                Protocol
                              FastEthernet0/0            unassigned      YES NVRAM  up                    up
                              FastEthernet0/0.1          192.168.0.11    YES NVRAM  up                    up
                              FastEthernet0/0.2          192.168.32.11   YES NVRAM  up                    up
                              FastEthernet0/0.3          192.168.33.11   YES NVRAM  up                    up
                              FastEthernet0/0.4          unassigned      YES unset  up                    up
                              FastEthernet0/0.5          unassigned      YES unset  up                    up
                              FastEthernet0/0.6          unassigned      YES unset  up                    up
                              FastEthernet0/0.7          unassigned      YES unset  up                    up
                              FastEthernet0/0.8          unassigned      YES unset  up                    up
                              FastEthernet0/0.9          unassigned      YES unset  up                    up
                              Serial0/0                  unassigned      YES NVRAM  administratively down down
                              BRI0/0                     unassigned      YES NVRAM  up                    up
                              BRI0/0:1                   unassigned      YES unset  down                  down
                              BRI0/0:2                   unassigned      YES unset  down                  down
                              Serial0/1                  unassigned      YES NVRAM  administratively down down
                              Serial1/0                  unassigned      YES NVRAM  administratively down down
                              Serial1/1                  unassigned      YES NVRAM  up                    up
                              Serial1/2                  unassigned      YES NVRAM  administratively down down
                              Serial1/3                  unassigned      YES NVRAM  up                    up
                              Serial1/4                  unassigned      YES NVRAM  down                  down
                              Serial1/5                  unassigned      YES NVRAM  administratively down down
                              Serial1/6                  unassigned      YES NVRAM  administratively down down
                              Serial1/7                  unassigned      YES NVRAM  up                    up
                              Loopback6                  203.0.0.1       YES NVRAM  up                    up

                               

                              ---------------------------------------------------------------------------

                               

                              After:

                               

                              Router4(config)#do sh ip int brie
                              Interface                  IP-Address      OK? Method Status                Protocol
                              FastEthernet0/0            unassigned      YES NVRAM  up                    up
                              FastEthernet0/0.1          192.168.0.11    YES NVRAM  up                    up
                              FastEthernet0/0.2          192.168.32.11   YES NVRAM  up                    up
                              FastEthernet0/0.3          192.168.33.11   YES NVRAM  up                    up
                              FastEthernet0/0.4          unassigned      YES unset  up                    up
                              FastEthernet0/0.5          unassigned      YES unset  up                    up
                              FastEthernet0/0.6          unassigned      YES unset  up                    up
                              FastEthernet0/0.7          unassigned      YES unset  up                    up
                              FastEthernet0/0.8          unassigned      YES unset  up                    up
                              FastEthernet0/0.9          unassigned      YES unset  up                    up
                              Serial0/0                  unassigned      YES NVRAM  administratively down down
                              BRI0/0                     unassigned      YES NVRAM  up                    up
                              BRI0/0:1                   unassigned      YES unset  down                  down
                              BRI0/0:2                   unassigned      YES unset  down                  down
                              Serial0/1                  unassigned      YES NVRAM  administratively down down
                              Serial1/0                  unassigned      YES NVRAM  administratively down down
                              Serial1/1                  10.10.10.1      YES manual up                    up
                              Serial1/2                  unassigned      YES NVRAM  administratively down down
                              Serial1/3                  unassigned      YES NVRAM  up                    up
                              Serial1/4                  unassigned      YES NVRAM  down                  down
                              Serial1/5                  unassigned      YES NVRAM  administratively down down
                              Serial1/6                  unassigned      YES NVRAM  administratively down down
                              Serial1/7                  unassigned      YES NVRAM  up                    up

                               

                              -------------------------------------------------------------------------------

                               

                              Hope this is some help

                               


                              Please post if anyone finds out more

                               


                              B