If you go to http://tools.cisco.com/ITDIT/CFN/jsp/index.jsp
You can then search by feature. Type the feature "ip sla responder" continue, then select platform, and you will see all the available options.
Any of the below 64 will work for you.
12.2(44)SE1 IP BASE c3560-ipbasek9-mz.122-44.SE1.bin 128 16 12.2(44)SE1 IP BASE W/O CRYPTO c3560-ipbase-mz.122-44.SE1.bin 128 16 12.2(44)SE1 IP SERVICES c3560-ipservicesk9-mz.122-44.SE1.bin 128 16 12.2(44)SE1 IP SERVICES W/O CRYPTO c3560-ipservices-mz.122-44.SE1.bin 128 16 12.2(44)SE ADVANCED IP SERVICES c3560-advipservicesk9-mz.122-44.SE.bin 128 16 12.2(44)SE IP BASE c3560-ipbasek9-mz.122-44.SE.bin 128 16 12.2(44)SE IP BASE W/O CRYPTO c3560-ipbase-mz.122-44.SE.bin 128 16 12.2(44)SE IP SERVICES c3560-ipservicesk9-mz.122-44.SE.bin 128 16 12.2(44)SE IP SERVICES W/O CRYPTO c3560-ipservices-mz.122-44.SE.bin 128 16 12.2(40)SE ADVANCED IP SERVICES c3560-advipservicesk9-mz.122-40.SE.bin 128 16 12.2(40)SE IP BASE c3560-ipbasek9-mz.122-40.SE.bin 128 16 12.2(40)SE IP BASE W/O CRYPTO c3560-ipbase-mz.122-40.SE.bin 128 16 12.2(40)SE IP SERVICES c3560-ipservicesk9-mz.122-40.SE.bin 128 16 12.2(40)SE IP SERVICES W/O CRYPTO c3560-ipservices-mz.122-40.SE.bin 128 16
It may still be the "rtr" command set there...
Uber-Geek-SW1(config)#ip sla ?
<1-2147483647> Entry Number
ethernet-monitor IP SLAs Auto Ethernet configuration
group Group Configuration or Group Scheduling
key-chain Use MD5 authentication for IP SLAs control message
logging Enable Syslog
low-memory Configure Low Water Memory Mark
reaction-configuration IP SLAs Reaction-Configuration
reaction-trigger IP SLAs Trigger Assignment
reset IP SLAs Reset
responder Enable IP SLAs Responder
restart Restart An Active Entry
schedule IP SLAs Entry Scheduling
slm Service Level Management
Uber-Geek-SW1(config)#do sh ver | in bin
System image file is "flash:/c3560-advipservicesk9-mz.122-46.SE.bin"
Works for me though.
SW4(config)#do show ver | i file
System image file is "flash:/c3560-advipservicesk9-mz.122-35.SE5.bin"
SW4(config-rtr)#type dns target www.cicco.com name 10.2.2.2
Yes, the earlier feature set is supported. Thanks, once again time to understand the requirement. If the requirement was to use Cisco IOS IP SLA then you need a later version of code. However, if the goal was to validate some condition and then take Y action, the older RTR is in fact available. Just need to remember in the older rtr responder there are fewer operations available. I needed to remember the older syntax, there are actually (3) main syntax differences based on the IOS version... I could have been burned on the actual lab, because I was not considering the older command set. Thanks Scott for the refresher!
dhcp DHCP Operation
dns DNS Query Operation
echo Echo Operation
ftp FTP Operation
http HTTP Operation
jitter Jitter Operation
pathEcho Path Discovered Echo Operation
pathJitter Path Discovered Jitter Operation
slm SLM Operation
tcpConnect TCP Connect Operation
udpEcho UDP Echo Operation