to follow, share, and participate in this socialgroup. Not a member? Join Now!
Note: The following content is provided "as is." This page originally referenced an archived discussion on the old VIRL dev-innovate forum. Since that site is no longer available, I have simply the content... http://www.scsiraidguru.com/VIRL/VIRLSims/DHCP/ I will add the picture tonight subinterfaces between iosv-1 and iosv-6 relay from iosv-6 for iosv-7 http://www.scsiraidguru.com/VIRL/VIRLSims/SLAAC/ I will add a picture tonight. subinterfaces between iosv-1 and iosv-6 relay from iosv-6 for iosv-7 Hi All, I have had to rebuild my VIRL server on VMware Workstation. The installation was fine, and connectivity to the Internet is fine. However, I am getting the below error message. I have setup the server u... email@example.com Hello, Please i need help to get the VIRL working. i'm getting this error Failed to collect current salt contact status: Cisco contact was not established. This may be temporary. Please mak... Hi, we want to configure XR Traffic Controller (XTC) on Cisco XRV9000 (on the VRIL), but unfortunately, I couldn't use this feature (cpe command ) on the IOSXRV 9000.So, Let me know if this feature is supported by V... Hi All, Everytime i start a virl server on packet, even though i have reset the license key but the following error keeps popping up. Any ideas, how to fix it? The license subscription still got about ... virl@virl:~$ sudo salt-call --local grains.get id local: 78KJqXmW.virl.info virl@virl:~$ sudo salt-minion -l debug [DEBUG ] Reading configuration from /etc/salt/minion [DEBUG &... Hello Virl1.3 (Ubuntu Server) have changed not use GUI? How can activate my license, please tell me? VIRL-PE 1.3 Release Overview: Lesson 2: Installing Cisco VIRL-PE 1.3 Best Regards, Mike Hello All, I have setup a lab using Nxosv-9000 on virl 1.3.296 where I am trying to setup VxLAN using PIM (not evpn or fabricpath). After configuring pim, vlan/vxlan association and nve I am still not able to ... Summary If the user needs to deploy a new VIRL server from OVA or bare metal, there may be images of simulation nodes (snap shots or third party VMs) which the user may want to transfer. At this time, there is no auto... I have decided to purchase VIRL , but before placing order I want to confirm the following. 1) Does the VIRL supports ASR 5500 to simulate MME- EPC components configuration? 2) Can I interface the LTE R... Hello since yesterday I am facing the following issue: I have reset Keys and ID a couple of times but the issue persists. If anyone knows how to fix it, please let me know. I was looking for information on what access to the internet is needed to run VIRL and what the access is for? I thought I remember seeing something that said rules were needed just for software updates, but when I tr... Hi there, I purchased a VIRL 20 Nodes license and want to download the image for VIRL and of the routing equipment ( for GNS3 ) . But I can't find the images on the website.. everytime a followed GNS3 I will b... How do I get TAC support for VIRL? I spend most of my time troubleshooting the software instead of doing labs. Alejo, Now VIRL is stuck in maintenance mode? I found a thread that gave some x-term commands to clear out the message but they are working. How do I get VIRL from stuck in maintenance mode? Thanks, Alan Before I Purchase
Supported Cisco OS Features in VIRL
Using VIRL (Advanced features)
VIRL for Certifications and Sample Topologies
Release notes a... I have not started up Uwm in a while and now when I rebooted the VIRL vm it will not allow me to login. I have tried the uwmadmin/password for creds but no luck. Is there a way to reset this via the virl s... http://www.scsiraidguru.com/VIRL/VIRLSims/LoopPrevention2/ I put Sh Run, Sh IP Route and Sh IPv6 Route on the page. I have both IPv4 and IPv6 configured at every link. ...